Hud Handrailing - REO Property Preservation Forum
 
LinkBack Thread Tools Display Modes
post #1 of 5 (permalink) Old 05-31-2013, 07:32 PM Thread Starter
Senior Member
 
GaReops's Avatar
 
Join Date: Aug 2012
Location: Georgia
Posts: 121
Thanks: 11
Thanked 41 Times in 27 Posts
Hud Handrailing

Has HUD changed about their hand railing requirements? I thought it was 4 steps or 30" for decks,balconies, etc? I was told something totally different today....
GaReops is offline  
Sponsored Links
Advertisement
 
post #2 of 5 (permalink) Old 06-01-2013, 02:46 PM
Senior Member
 
BamaPPC's Avatar
 
Join Date: May 2012
Location: Alabama
Posts: 414
Thanks: 95
Thanked 283 Times in 133 Posts
Haven't heard of any changes. But, the best place to check on HUD requirements is HUD.gov
BamaPPC is offline  
post #3 of 5 (permalink) Old 06-02-2013, 07:33 AM
P3+
Motivator
 
P3+'s Avatar
 
Join Date: Aug 2012
Posts: 267
Thanks: 41
Thanked 166 Times in 79 Posts
No idea what HUD may be requiring these days but here is IRC's code requirements:

46. LANDINGS. Section R311 IRC 2009
R311.7.5 Landings for stairways. There shall be a floor or landing at the top and bottom of each stairway.
Exception: A floor or landing is not required at the top of an interior flight of stairs, including stairs in an
enclosed garage, provided a door does not swing over the stairs. A flight of stairs shall not
have a vertical rise larger than 12 feet (3658 mm) between floor levels or landings. The
width of each landing shall not be less than the width of the stairway served. Every landing
shall have a minimum dimension of 36 inches (914 mm) measured in the direction of travel.
R311.3 Floors and landings at exterior doors. There shall be a landing or floor on each side of each exterior door. The
width of each landing shall not be less than the door served. Every landing shall have a minimum dimension of 36 inches
(914 mm) measured in the direction of travel. Exterior landings shall be permitted to have a slope not to exceed 1/4 unit
vertical in 12 units horizontal (2-percent).
Exception: Exterior balconies less than 60 square feet (5.6 m2) and only accessible from a door are permitted to
have a landing less than 36 inches (914 mm) measured in the direction of travel.
47. WIDTH. Section R311.7.1 IRC 2009
Stairways shall not be less than 36 inches (914 mm) in clear width at all points above the permitted handrail height and
below the required headroom height. Handrails shall not project more than 4.5 inches (114 mm) on either side of the
stairway and the minimum clear width of the stairway at and below the handrail height, including treads and landings,
shall not be less than 31.5 inches (787 mm) where a handrail is installed on one side and 27 (698 mm) where handrails are
provided on both sides.
Exception: The width of spiral stairways shall be in accordance with Section R311.5.8.
48. RISE AND RUN. Section R311.7.4 IRC 2009
R311.7.3 Walkline. The walkline across winder treads shall be concentric to the curved direction of travel through the
turn and located 12 inches (305 mm)from the side where the winders are narrower. The 12-inch (305 mm) dimension shall
be measured from the widest point of the clear stair width at the walking surface of the winder. If winders are adjacent
within the flight, the point of the widest clear stair width of the adjacent winders shall be used.
R311.7.4 Stair treads and risers. Stair treads and risers shall meet the requirements of this section. For the purposes of
this section all dimensions and dimensioned surfaces shall be exclusive of carpets, rugs or runners.
R311.7.4.1 Riser height. The maximum riser height shall be 73/4 inches (196 mm). The riser shall be measured vertically
between leading edges of the adjacent treads. The greatest riser height within any flight of stairs shall not exceed the
smallest by more than 3/8 inch (9.5 mm).
R311.7.4.2 Tread depth. The minimum tread depth shall be 10 inches (254 mm). The tread depth shall be measured
horizontally between the vertical planes of the foremost projection of adjacent treads and at a right angle to the tread's
leading edge. The greatest tread depth within any flight of stairs shall not exceed the smallest by more than 3/8 inch (9.5
mm). Consistently shaped winders at the walkline shall be allowed within the same flight of stairs as rectangular treads
and do not have to be within 3/8 inch (9.5 mm) of the rectangular tread depth. Winder treads shall have a minimum tread
depth of 10 inches (254 mm) measured between the vertical planes of the foremost projection of adjacent treads at the
intersections with the walkline. Winder treads shall have a minimum tread depth of 6 inches (152 mm) at any point within
the clear width of the stair. Within any flight of stairs, the largest winder tread depth at the walkline shall not exceed the
smallest winder tread by more than 3/8 inch (9.5 mm).
49. PROFILE. Section R311.7.4.3 IRC 2009
The radius of curvature at the leading edge of the tread shall be no greater than 9/16 inch (14.3 mm). A nosing not less
than 3/4 inch (19 mm) but not more than 1 1/4 inch (32 mm) shall be provided on stairways with solid risers. The greatest
nosing projection shall not exceed the smallest nosing projection by more than 3/8 inch (9.5 mm) between two stories, including the nosing at the level of floors and landings. Beveling of nosing shall not exceed 1/2 inch (12.7 mm). Risers
shall be vertical or sloped from the underside of the leading edge of the tread above at an angle not more than 30 (0.51
rad) degrees from the vertical. Open risers are permitted, provided that the opening between treads does not permit the
passage of a 4-inch diameter (102 mm) sphere.
Exceptions:
1. A nosing is not required where the tread depth is a minimum of 11 inches (279 mm).
2. The opening between adjacent treads is not limited on stairs with a total rise of 30 inches (762 mm) or less.
50. HEADROOM. Section R311.7.2 IRC 2009
R311.7.2 Headroom. The minimum headroom in all parts of the stairway shall not be less than 6 feet 8 inches (2032 mm)
measured vertically from the sloped line adjoining the tread nosing or from the floor surface of the landing or platform on
that portion of the stairway.
Exception: Where the nosings of treads at the side of a flight extend under the edge of a floor opening
through which the stair passes, the floor opening shall be allowed to project horizontally into
the required headroom a maximum of 43/4 inches (121 mm).
51. SPACE UNDER STAIRS. Section R302.7 IRC 2009
Under stair protection. Enclosed accessible space under stairs shall have walls, under-stair surface and any soffits
protected on the enclosed side with 1/2-inch (12.7 mm) gypsum board.
52. HANDRAILS. Section R311.7.6 IRC 2009
R311.7.6 Handrails. Handrails shall be provided on at least one side of each continuous run of treads or flight with four
or more risers.
R311.7.7.1 Height. Handrail height, measured vertically from the sloped plane adjoining the tread nosing, or finish
surface of ramp slope, shall be not less than 34 inches (864 mm) and not more than 38 inches (965 mm).
Exceptions:
1. The use of a volute, turnout or starting easing shall be allowed over the lowest tread.
2. When handrail fittings or bendings are used to provide continuous transition between
flights, the transition from handrail to guardrail, or used at the start of a flight, the
handrail height at the fittings or bendings shall be permitted to exceed the maximum
height.
R311.7.7.2 Continuity. Handrails for stairways shall be continuous for the full length of the flight, from a point directly
above the top riser of the flight to a point directly above lowest riser of the flight. Handrail ends shall be returned or shall
terminate in newel posts or safety terminals. Handrails adjacent to a wall shall have a space of not less than 1 1/2 inch (38
mm) between the wall and the handrails.
Exceptions:
1. Handrails shall be permitted to be interrupted by a newel post at the turn.
2. The use of a volute, turnout, starting easing or starting newel shall be allowed over the lowest tread.
R311.7.7.3 Handrail grip size. All required handrails shall be of one of the following types or provide equivalent
graspability.
1. Type I. Handrails with a circular cross section shall have an outside diameter of at least 11/4 inches
(32 mm) and not greater than 2 inches (51 mm). If the handrail is not circular, it shall have a perimeter
dimension of at least 4 inches (102 mm) and not greater than 61/4 inches (160 mm) with a maximum
cross section of dimension of 2 1/4 inches (57 mm). Edges shall have a minimum radius of 0.01 inch
(0.25 mm).
2. Type II. Handrails with a perimeter greater than 6 1/4 inches (160 mm) shall provide a graspable
finger recess area on both sides of the profile. The finger recess shall begin within a distance of
inch (19 mm) measured vertically from the tallest portion of the profile and achieve a depth of at least
5/16 inch (8 mm) within 7/8 inch (22 mm) below the widest portion of the profile. This required depth
shall continue for at least 3/8 inch (10 mm) to a level that is not less than 1 3/4 inches (45 mm) below
the tallest portion of the profile. The minimum width of the handrail above the recess shall be 1
P3+ is offline  
Sponsored Links
Advertisement
 
post #4 of 5 (permalink) Old 06-02-2013, 07:34 AM
Business Consultant
 
Cleanupman's Avatar
 
Join Date: Nov 2012
Location: Silver Springs, Nevada
Posts: 1,380
Thanks: 322
Thanked 564 Times in 339 Posts
So there you have it....
What were you told?????

Aladay LLC
Property Preservation
New Business Consultant
Custom Glass&Wood
Cleanupman is offline  
post #5 of 5 (permalink) Old 06-02-2013, 08:31 AM
P3+
Motivator
 
P3+'s Avatar
 
Join Date: Aug 2012
Posts: 267
Thanks: 41
Thanked 166 Times in 79 Posts
Another thing to note, the 2x4 handrails that many of you are installing are NOT code compliant. They are not considered grippable and should someone use it and get hurt falling down the stairs it can and will come back on you. So when these service companies tell you to just throw a 2x4 or 2x3 up as a handrail....tell them NO and demand to be paid more money for a compliant rail.

See diagram in link to acceptable profiles.

http://www.co.stevens.wa.us/landserv...WAYSECTION.pdf
P3+ is offline  
The Following User Says Thank You to P3+ For This Useful Post:
BRADSConst (06-02-2013)
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the REO Property Preservation Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome